Aggregator

Log Number: 4490835Logbook(s): 

• ELOG

Tags: 

• Autolog

Body: 

The following box supplies were TURNED OFF by version 2-16 of the Box Supply Cycling Script:
ARC7A Ramp Rate = 8.659 A/s

Log Number: 4490834Logbook(s): 

• ELOG

Tags: 

• Autolog

Body: High Voltage was turned off for:
R23
R24
R25
R26
R27
R28
R29
R2A
R2B
R2C
R2D
R2E
R2F
R2G
R2H
R2I
R2J
R2K
R2L
R2M
R2N
R2O
R2P
R2Q

Log Number: 4490833Logbook(s): 

• DCLOG
• ELOG

Entry Makers: msmithBody: 

Magnet mismatched and would not take setpoint. I went out to the service building to swap the trim card, but the mismatch alarm went away before the swap happened. Instead, I just reseated the card and we cycled the magnet.

Zooming way in on the myaplot show a small increase in current while nobody was working on it.

Log Number: 4490832Logbook(s): 

• ELOG

Tags: 

• Autolog

Body: System UN-Masking for: CryoModule
User: kprice
Areas: NorthLinac SouthLinac

CryoModule Devices:
1L14
1L03
1L02
1L04
1L05
1L07
1L06
1L08
1L09
1L10
1L11
1L12
1L15
1L13
1L16
1L19
1L17
1L18
1L20
1L21
1L22
1L23
1L24
1L25
1L26
2L14
2L03
2L02
2L04
2L05
2L07
2L06
2L08
2L11
2L09
2L10
2L12
2L15
2L13
2L16
2L19
2L17
2L18
2L20
2L21
2L22
2L23
2L24
2L25
2L26

Log Number: 4490831Logbook(s): 

• POLOG
• ELOG

Body: Spot Location: (13250,19250), Charge: 20.758823999999994

Laser Wavelength Atten Setting Laser Power Current HV PS Current QE PV Updated? Update Time/Reason Not Updated (nm) (W) (uA)</

Log Number: 4490830Logbook(s): 

• ELOG

Body: 

Thanks for putting this ATLis in. Job looks good, Approved. RRD on-issue.

Log Number: 4490828Logbook(s): 

• ELOG

Tags: 

• Autolog

Body: System Masking for: CryoModule
User: kprice
Areas: NorthLinac SouthLinac

CryoModule Devices:
1L14
1L03
1L02
1L04
1L05
1L07
1L06
1L08
1L09
1L10
1L11
1L12
1L15
1L13
1L16
1L19
1L17
1L18
1L20
1L21
1L22
1L23
1L24
1L25
1L26
2L14
2L03
2L02
2L04
2L05
2L07
2L06
2L08
2L11
2L09
2L10
2L12
2L15
2L13
2L16
2L19
2L17
2L18
2L20
2L21
2L22
2L23
2L24
2L25
2L26

Log Number: 4490827Logbook(s): 

• ELOG

Tags: 

• Autolog

Body: System UN-Masking for: BeamLossMonitor
User: kprice
Areas: All

BeamLossMonitor Devices:
ILM0I07
ILM0L01A
ILM0L01B
ILM0L02
ILM2D00A
ILM2D00B
ILM0L04A
ILM0L04B
ILM0L05
ILM0L06A
ILM0L08
ILM0R01
ILM4D00
ILM0R03
ILM0R04
ILM0R06
ILM0R08
ILM0R09
ILM1L01
ILM1L02
ILM6R08
ILM3S00
ILM7S00
ILM9S00
ILM5S10
ILM5E03
ILM7S01
ILM9A01
ILM3E02
ILM5A01
ILM1A04
ILM1A06
ILM1A09
ILM5A10
ILM1A16
ILM1A19
ILM3R10
ILM9R07
ILM1R09
ILM2L03
ILM5R10
ILM5R05
ILM2L01
ILM2T09
ILM8

Log Number: 4490826Logbook(s): 

• DEGRADERLOG
• ELOG

Entry Makers: bschaumlBody: 

- Restored allsave 27034
- Retracted target ladder and apertures
- Unmasked/masked FSD nodes to match gold mask
- Set MPT0L02 to zero BdL, cycled, and turned power supply off

Log Number: 4490825Logbook(s): 

• ELOG

Tags: 

• Autolog

Body: saver ran from opsl01
Data from: /usr/opdata/burt/allsnap/04-24-26_01:15:31
Restored file: /tmp/04-24-26_04:27:19.snap


Backing out of BSLIST 119067

Log Number: 4490824Logbook(s): 

• ELOG

Tags: 

• Autolog

Body: saver ran from opsl01

Saved: bschauml 04-24-26 04:27:06 {A:i B:3 C:2 E:345 A=BS B=BS C=BS D=BS 0R08=0.00 0R08 dump in. Autosave prior to restore.

Log Number: 4490823Logbook(s): 

• DEGRADERLOG
• ELOG

Entry Makers: bschaumlBody: 

We set the aspect ratio on target ladder viewer per SME's calculations and found some perplexing shifts in the X and Y sigmas of our harp scans at various solenoid currents. We attempted a few different aspect ratios in hopes of getting a round beam throughout our various solenoid setpoints but were unable to sort out exactly what was going on. Further analysis is necessary.