Recent Log Entries

iocnl22rffcc1 restoration failed

Log Number: 3997166Logbook(s): Tags: Body: restorelib 2.4 Target restore date was 2022-05-26 10:48:42 The output from the myRestore execution was as follows: iocnl22rffcc1 Rf12Fcc_zzz Pause: 60 second(s) Execute: /cs/opshome/burt/REBOOT/Rf12Fcc/DLOAD_ICAL.csh iocnl22rffcc1 (success) c100_rffcc@2022-05-26 10:48 35(35) restored c100_ecal@2022-05-26 10:48 17(17) restored Execute: myRestore -execute -P c100_ecal -t R1M1_ECAL -m BLDGNUM=1 ZONE=M CAV=1 (failure) <MyRestore URL>: Error status returned [Save not found.] Execute: burtwb -r 3 -f /cs/opshome/burt/REBOOT/Rf12F

CREW CHIEF SIGN IN

Log Number: 3997162Logbook(s): Body: 
THOMAS JEFFERSON NATIONAL ACCELERATOR FACILITY
ACCELERATOR OPERATIONS CREW CHIEF SIGN IN FORM

Date : 05-27-22
Time : 06:57:26
Day : Friday
Shift : Day

Crew Chief : Merz
Program Deputy: Spata
Team : B
Arm : RADCON
Designated SSO: Blackshaw
LERF Operator:
Operators : Blackshaw

This stamp certifies that the above Crew Chief has read/reviewed/received the following:

QE Measurement

Log Number: 3997159Logbook(s): Body: Spot Location: (13000.0,18250.0), Charge: 3.822482

Laser Wavelength Atten Setting Laser Power Current HV PS Current QE PV Updated? Update Time/Reason Not Updated (nm) (W) (uA)

Autolog restore

Log Number: 3997158Logbook(s): Tags: Body: saver ran from opsl07
Data from: /usr/opdata/burt/allsnap/05-26-22_20:28:54
Restored file: /tmp/05-27-22_03:31:47.snap


Restored to settings as found before rayTrace studies

Autolog save

Log Number: 3997157Logbook(s): Tags: Body: saver ran from opsl07

Saved: dturner 05-27-22 03:31:33 {A:2 B:1 C:5 E:1047 A=BS B=BS C=BS D=BS 0R08=0.00 0R08 dump in. Autosave prior to restore.

COMMENT ON Verify proper Wien quad behavior

Log Number: 3997155Logbook(s): Body: 

Paul,

The BDL range is found by trial and error at this point. I pick a range of BDLs that go from a large beam size, to a minimum, and back again.

I'd like to set the Wiens to settings we're likely to use in the near future.

I should have stated that the SMEs would be performing this task. It slipped my mind to mark the testplan appropriately.

MQW1I06 behavior with HWien on and off

Log Number: 3997152Logbook(s): Entry Makers: dturnerBody: 

I used the qsUtility zigzag data collection tool to plot beam size vs K1 (BDL) for MQW1I06 for both planes and with both the HWien off and at -42 degrees.

At first glance, MQW1I06 seems to exhibit no behavior unbecoming of a proper quad in either case with the HWien off or at +42 degrees.

IHA0I02 Y-plane Emittance Measurement Analysis - MQW1I06, HWien off

Log Number: 3997151Logbook(s): Body: IHA0I02 Y-plane Emittance Measurement Analysis - MQW1I06, HWien off
qsUtility Data Analyzer V7-15
SDDS FILE: /cs/prohome/apps/q/qsUtility/7-15/fileio/data/IHA0I02/IHA0I02_y_zigzag_2022-05-27_02:41:16/IHA0I02_zigzag_2022-05-27_02:41:16_qsUtility_analyzer.sdds
CED WORKSPACE: OPS CED LOGIN KEY: pro

IHA0I02 X-plane Emittance Measurement Analysis - MQW1I06, HWien off

Log Number: 3997149Logbook(s): Body: IHA0I02 X-plane Emittance Measurement Analysis - MQW1I06, HWien off
qsUtility Data Analyzer V7-15
SDDS FILE: /cs/prohome/apps/q/qsUtility/7-15/fileio/data/IHA0I02/IHA0I02_x_zigzag_2022-05-27_02:20:35/IHA0I02_zigzag_2022-05-27_02:20:35_qsUtility_analyzer.sdds
CED WORKSPACE: OPS CED LOGIN KEY: pro

IHA0I02 Y-plane Emittance Measurement Analysis - MQW1I06, HWien +42

Log Number: 3997146Logbook(s): Body: IHA0I02 Y-plane Emittance Measurement Analysis - MQW1I06, HWien +42
qsUtility Data Analyzer V7-15
SDDS FILE: /cs/prohome/apps/q/qsUtility/7-15/fileio/data/IHA0I02/IHA0I02_y_zigzag_2022-05-27_01:34:47/IHA0I02_zigzag_2022-05-27_01:34:47_qsUtility_analyzer.sdds
CED WORKSPACE: OPS CED LOGIN KEY: pro

Pages