Recent Log Entries

Log Number: 4158777Logbook(s): 

• ELOG

Body: 

With Marcy's guidance, the two flange mounted NEG pumps in the space between buncher and dipole chamber were conditioned (3V with 15 minute ramp and 30 minute soak - this provides ~ 2.5 A through each NEG pump). VGP0I06 and VGP1D00A. Pressure at turbo pump cart started ~ 1E-7 Torr and increased to midE-5Torr and then rolled over. Afterwards, pressure dropped fast. I burped the ion pumps once. Then after waiting for pump cart pressure to reach 3E-7Torr, I turned ion pumps ON and closed RA valve to pump cart. Ion pump current combined (two pumps) ~ 200 uA and falling.

Log Number: 4158776Logbook(s): 

• ELOG
• SLOG

Tags: 

• Autolog

Body: restorelib 2.6 Target restore date was 2023-05-23 14:27:41 The output from the myRestore execution was as follows: iocnl26rffcc3 Rf12Fcc Pause: 60 second(s) Execute: /cs/opshome/burt/REBOOT/Rf12Fcc/DLOAD_ICAL.csh iocnl26rffcc3 (success) c100_rffcc@2023-05-23 14:27 32(32) restored Execute: burtwb -r 3 -f /cs/opshome/burt/REBOOT/Rf12Fcc/snap-ecal/iocnl26rffcc3-ecal.snap (success) Execute: burtwb -r 3 -f /cs/opshome/burt/REBOOT/Rf12Fcc/snap-exp/iocnl26rffcc3-exp.snap (success) Execute: /cs/opshome/burt/REBOOT/Rf12Fcc/GGTmyRestore.csh iocnl26rf

Log Number: 4158775Logbook(s): 

• ELOG
• SLOG

Tags: 

• Autolog

Body: restorelib 2.6 Target restore date was The output from the myRestore execution was as follows: <MyAPI>: Channel lookup fault [VIP0L00MIN]

Log Number: 4158774Logbook(s): 

• ELOG
• SLOG

Tags: 

• Autolog

Body: Event/action ID: 3 [mod.type.prop.ioc.macaddress]
Deployment: ced
Workspace: ops
Changes:
iocin04rfint.macaddress

Log Number: 4158773Logbook(s): 

• POLOG
• ELOG

Body: 

the two ion pumps in region where Marcy activated the NEG pumps are happy, with pump current ~ 4uA for each pump and falling. I suspect the pump current will be sub-microAmp by tomorrow. Good work

Log Number: 4158772Logbook(s): 

• ELOG
• SLOG

Tags: 

• Autolog

Body: restorelib 2.6 Target restore date was The output from the myRestore execution was as follows: <MyAPI>: Channel lookup fault [VIP0L00MIN]

Log Number: 4158771Logbook(s): 

• ELOG
• SLOG

Tags: 

• Autolog

Body: restorelib 2.6 Target restore date was The output from the myRestore execution was as follows: <MyAPI>: Channel lookup fault [VIP0L00MIN]

Log Number: 4158770Logbook(s): 

• CLOG
• ELOG
• SRFLOG

Body: 

JTs have been set to fill to 90%

Log Number: 4158769Logbook(s): 

• ELOG

Body: 

starting pumping on the 6A line

Log Number: 4158768Logbook(s): 

• POLOG
• ELOG

Entry Makers: marcyBody: 

Activated AIPINJ2 girder 2 NEG pumps.

Yesterday, ramp to condition mode (250C for DP, 3V 2A for z100)
Today, full activation
Ramp time: 15 min. Soak for 75 min instead of 60 since temperature rise was slow.
P(max) at cart was 4e-4 Torr at ~15 minutes in. By end, pressure at cart had fallen to 1.7e-7 Torr.

Ion pumps turned on from pumpout port away to all pumps in section of beamline, and VBV0I05/6 (upstream of DP can) closed manually with screwdriver once VIP0I06 and VIP0I07 were energized and below 65 uA.

Beamline roughing valve closed, turbo cart left on for future work.

Log Number: 4158767Logbook(s): 

• ELOG
• SLOG

Tags: 

• Autolog

Body: restorelib 2.6 Target restore date was The output from the myRestore execution was as follows: <MyAPI>: Channel lookup fault [VIP0L00MIN]

Log Number: 4158766Logbook(s): 

• ELOG
• SLOG

Tags: 

• Autolog

Body: restorelib 2.6 Target restore date was 2023-05-23 11:53:26 The output from the myRestore execution was as follows: iocin2 <NOTE> Rf6Cryo: Provided macro *CAV* is never used <NOTE> Rf6Ops: Provided macro *IOC* is never used BL_iocin2@2023-05-23 11:53 4(4) restored Rf6Cryo Execute: burtwb -f /cs/opshome/burt/REBOOT/rf/snap/iocin2heatdisvINIT.snap (success) Execute: burtwb -f /cs/opshome/burt/REBOOT/rf/snap/iocin2heatmodemanual.snap (success) Pause: 8 second(s) Rf06Cryo_heatset@2023-05-23 11:53 2(2) restored Pause: 8 second(s

Log Number: 4158765Logbook(s): 

• ELOG
• INCLOG

Body: 

Disassembled the viewer. Replaced the chromox target with the YAG crystal. Replaced the bellows assembly with the new one. Aligned the target holder shaft at 45 degrees upstream beam direction. Inserted the viewer, and adjusted the turn buckle to center the YAG target. Installed the viewer assembly back on to the 4D00 beam line. Viewer mechanical work complete.

Log Number: 4158764Logbook(s): 

• ELOG

Body: 

Approved

Log Number: 4158763Logbook(s): 

• ELOG

Body: 

Approved and thank you

Log Number: 4158761Logbook(s): 

• CLOG
• ELOG
• SRFLOG

Body: 

Vacuums and diodes look good.

Log Number: 4158760Logbook(s): 

• CLOG
• ELOG
• RFLOG
• SRFLOG

Body: 

2L24 and 2L25 u-tubes have been installed. SRF has been notified that they are ready for cooldown.

Log Number: 4158759Logbook(s): 

• ELOG
• INCLOG

Entry Makers: sethgcumbiadsjamessawyerbevinsBody: 

After the breaker exercises a while ago, IOCSE8 and IOCSE15 have not been able to come up properly, even after a hard reboot. So, after some investigation from Brian Bevins and Brad Cumbia, we found out the transition module had to be replaced for both IOCs. After swapping out the transition modules the IOCs came up without an issue.

Log Number: 4158758Logbook(s): 

• ELOG
• SLOG

Tags: 

• Autolog

Body: restorelib 2.6 Target restore date was 2023-05-10 15:47:31 The output from the myRestore execution was as follows: iocse8 seebpm@2023-05-10 15:47 369(369) restored system@2023-05-10 15:47 2(2) restored Pause: 30 second(s) SEE_BURT 9(9) restored Execute: /usr/csite/certified/bin/ced2Epics -ced ced -A -s -i iocse8 (success) Procedure return status: Success

Log Number: 4158757Logbook(s): 

• ELOG

Body: 

Once the HI review has been conducted, consider this task approved.